KOBRA-3 DUAL ACE-PRO STAND

The Manifold error is usually on of the part not being fully recognized by the slicer due to some vertexes etc. You should have the option to repair. Also, Plate 3 is very similar to Plate 4 - being the side. Do you have this issue for plate 3? Lastly, I suspect the part will print without issue as there have been lots of s and prints of this model and this is the 1st time I hear of this. Do you want to try to print?

Yea, I don't think the Mac version has a repair option. That's why people were saying use Orca or the PC version of AC Slicer Next. I am printing plate 4 right now...no warnings and no issues so far. I will probably go ahead and try and print, though I hope it doesn't fail 4 hours into the 5-hour print. I'll let ya'll know...thx.

I meant printing plate 5 now. If no issues, I will try plate 4 and let you know. thx again.

Ok. Also, did you try with the phone app?

Oh, no...didn't try phone app. I will check that as well. About 15 minutes remaining on plate 5.

Actually, might have to wait until tomorrow. I will certainly give an update though. Everything has printed PERFECTLY so far...

Ok, printed almost perfectly. Something happens at layer 64 that causes a small area to not lay down. It looks like it will in now way affect functionality though. Also, to clarify, the error that comes up states, "Fix Model" feature is currently on on Windows. Please repair the model on AnycubicSlicerNext (Windows) or CAD softwares". Thx!!

I test printed the model in Windows using Ac slicer next and the model has 272 s and this is the 1st time this issue happens. I suspect it may be due to something in Ac slicer next for Mac which I cannot test with.

Never mind :) I can see from your pictures above that its not needed :) Cheers mate

No problem. If there is anything else let me know. Thank you

Hi the credenza is 20 inches or 50cm (approx.) The stand is not attached to the piece of wood. I used it for contrast. A black stand on a dark mahogany credenza is not that visible. Also you would probably want 24 inches of roll out although 20 inches is close. Let me know if you have other questions.

Just for clarity, since the Ace Pro is just over 11 inches deep, I assume the stand and roll out are about 12 inches deep, so when you completely roll out the bottom, the extra distance is to accommodate the distance the cover takes when it is opened up. Correct?

Yes that is the principle but a few comments. The Ace pro cannot sit flush against the wall on of the Bowden tubes and you have to allow for that. Also, I do not have 2 aces to test at the moment but the Ace stand is taller than the Ace and there is clearance between the lower Ace and the stand. As such you can replace filament with less roll-out distance but the lid will need to be held open. If you are really tight for space you can also set it up to roll sideways. You could also ask on Facebook in the K3 group as many have printed it. Hope this helps.

Thanks

No they won't but I have ed some add-ons. See the description for more details.

Thank you. If there are any other questions leave a comment or pm me.

Thank you for your comments. I have added a gif instruction video and a zip with the photos (if the gif video is too fast). Screws are 3.5 mm - 18 mm long. This model is for the STL - the design files are not included nor for sale.

I have purchased and ed the files, I have all the photos in the zip file, but there is no GIF video file among any of the files. Can you email it to me?

The gif video is not as part of the files - it is at the end of the model photos in the listing. They are the same as the zip file pictures. Regards

Thank you for your comments. I have added a gif instruction video and a zip with the photos (if the gif video is too fast). Screws are 3.5 mm - 18 mm long wood screws. You could have it on a shelf - I have it on a credenza but you need enough space for it to roll out.

Interesting since most our fasteners in the Americas come from Asia.